P-GA FUEL DISPENSER

P-GA FUEL DISPENSER

Pump Type: Optional

Inlet Pressure :>=54kPa.

Flow rate (L/min.) :55±5

Suction Distance (m) :6(verticalmente) / 50(orizzontalmente)

FlowMeter Type : Optional

Accuracy :±0.2%

Motor Voltage(V) :110V/220V/380V,50Hz/60Hz

Capacity(hp) :1HP(0.75kw)

Input Voltage : 110V/220V/380V,50Hz/60Hz

Nozzle :Auto Shut-off Nozzle

Environmental Condition : -40~~+55degree

Control Type: Solenold Vale Control Type

Preset :Function Provided(Small LCDIndicator)

Display(Counter) :Type LCD and Bright Backlight

Digit of Volume : 0~~999,999(6 Digits),Decimal point can be changed

Digit of Amount :0~~999,999(6 Digits),Decimal point can be changed

Digit of Unit price :0~~9999(4 Digits),Decimal point can be changed

Digit of Total Range :0~~99,999,999,99

Optional Display :Type LCD and Bright Backlight

Digit of Volume : 0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Amount : 0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Unit price :0~~999999(6 Digits),Decimal point can be changed

Digit of Total Range :0~~99,999,999,99

Totalizer: 1~~9,999,999

Hose :4.5m

Weight : 280kg

Dimension(L×W×H): 1060*550*1620(mm)

Dimension(L×W×H)Of Qty of Container : 40ft: 44 20ft: 22

As past over long service time, parts abrasion universally or cylinder severely damaged, a new measurement transducer should be installed to replace old one. As find exterior leakage, firstly inspect the bolts corresponding to leak section. Tightly screw loose bolts, if leakage is continued, disconnect and inspect the seal ring and gasket relative section. Substitute aging or damaged parts and reassemble. Apart from the above reasons of extensive colloid and surface abrasion, these trouble also cause abnormal operation of measurement transducer, such as position pin fall down from piston or deformation, small axis lost on upper and lower connecting rod, loose bolt between piston and connecting rod. The solution is that disassembli fuel dispenser ng measurem fuel dispenser ent transducer, replace damaged or unqualified components and reassemble. The fuel dispenser products made in normal factory seldom appear these troubles. Since measurement transducer is core component of fuel dispenser, elaborate machining, disconnection and reassembly should be as careful as possible. All elements should be cleaned before reassembly, excluding water into inner. Bolts are tightened even and appropriately. Soft-piston measurement transducer As these merits --- small in size, light weight, beautiful appearance, high accuracy, piston exchangeable--- soft-piston measurement transducer is widely adapted in domestic fuel dispenser market. It generally involves two structures: four-piston structure and double-piston structure. The latter model is selected universally. Therefore, this article will introduce the structure, working principal and maintenance of four- piston measurement transducer. Structure Diagram 2-20 and Diagram 2-21 show the cutaway view and exploded drawing of four-piston measurement transducer that is widely employed. The transducer mainly consists of sealed cover, upper subassembly, export axis, frame subassembly, piston subassembly, connecting rod and top cover, clearly presenting in Diagram 2-20 and Diagram 2-21. Diagram 2-20: Cutaway view

to examination ......................................................................................................... 15　　3.9 Terms relating to audit ...................................................................................................................... 16　　3.10 Terms relating to quality management or measurement processes .......................................... 18　　Annex A (informative) Methodology used in the development of the vocabulary ................................ 20　　Bibliography ...................................................................... fuel dispenser ........... fuel dispenser .............................................................. 29　　A fuel dispenser lphabetical index ..................................................................................................................................... 30　　 iii　　? ISO 2005 All rights reserved　　 www.bzxzw.com　　ISO 9000:2005(E)　　Foreword　　ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies　　(ISO member bodies). The work of preparing International Standards is normally carried out through ISO　　technical committees. Each member body interested in a subject for which a technical committee has been　　established has the right to be represented on that committee. International organizations governmental and　　non-governmental in liaison with ISO also take part in the work. ISO collaborates closely with the International　　Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.　　International Standards are drafted in acc

ve been strong, they argue, but it has boosted firms profits and raised earnings only for those at the top, while most Americans wages have stayed stagnant. With the benefits of the expansion so tilted to capital and the rich, they argue, focusing on the economy will help Democrats. Who is right? History is an imperfect guide. Ray Fair, an economist at Yale, famously devised an equation linking the outcome of presidential elections to inflation and output growth, but mid-terms are murkier. Divided government is one reason. Congress has often been controlled by a different party to the presidency, making mid-term elections less of a referendum on economic policy. And local issues often loom larger than the national economy fuel dispenser when it com fuel dispenser es to electing a congressman. Nor is the evidence from polls clear-cut. Ac fuel dispenser cording to Gallup s latest survey, only 39% of Americans approve of George Bush s handling of the economy, almost 10 percentage points fewer than in 2004. Almost 70% of them reckon economic conditions are getting worse, compared with less than half in 2004. That said, Americans perceptions of the actual state of the economy have not changed much. Both in 2004 and today just under 40% of people think it is in “excellent�or “good�shape a far higher share than in 1994, when control of Congress changed hands in a Republican landslide. Increased partisanship is also distorting people s perceptions of the economy. The share of Republicans who think it is in good shape is more than twice the share of Democrats. According to Gary Jacobson of the University of California, San Diego, only a small part of that gap can be explained by the fact that Republicans tend to be richer and are doing better in the expansion. Far more important, he reckons, is simple political bias. Nevertheless, it is hard to see how Republicans would gain from a campaign where the economy looms large. Since they control the presidency and Congress, all economic discomfort can be laid at their door. And t